HTG2.club
Home Theater Guide webboard => มุม Thai DIY Audio => ข้อความที่เริ่มโดย: NICKY ที่ 16 มกราคม, 2007, 11:45:24 pm
-
มี 6146W หลายสิบหลอด เอามาต่อ AMP ได้ไหมครับ
-
มี 6146W หลายสิบหลอด เอามาต่อ AMP ได้ไหมครับ
ได้ครับ
-
มี 6146W หลายสิบหลอด เอามาต่อ AMP ได้ไหมครับ
ได้ครับ
ใครช่วยหาวงจรดีๆให้ ผมให้ 4 หลอด NOS USA ( จะขอเพื่อนให้ ).
-
มี 6146W หลายสิบหลอด เอามาต่อ AMP ได้ไหมครับ
ได้ครับ
ใครช่วยหาวงจรดีๆให้ ผมให้ 4 หลอด NOS USA ( จะขอเพื่อนให้ ).
แบบนี้พอได้ไหมครับ วัตต์เยอะดี ชอบพุชพูลหรือเปล่าครับ
-
ภาคจ่ายไฟ
-
อันนี้วัตต์น้อยลงครับ พุชพูลเช่นกัน ผมมีหลอดเบอร์นี้ 1 หลอดครับ
-
โพสท์ใหญ่เลย(อยากได้หลอด) หลอดเบอร์นี้น่ารัก อ้วนจ้ำม่ำ มีหัวขุกด้วย
เพลทหนาปึ้ก ล่ำสันแบบนักยกน้ำหนักหญิง
ภาคจ่ายไฟที่เปลืองหลอดจังครับ
-
หลอดนี้ประมาณว่าเป็นหลอดเทตโธดใช้ในเครื่องส่งวิทยุ มีจุกแบบเดียวกับ 807
ถ้าผมทำก็คงเป็นซิงเกิลเอ็นด์ ดัดแปลงวงจรจาก 807 ครับ :headphone
-
แบบนี้ของ Ampeg Super Valve Tech. :cold
-
มี 6146W หลายสิบหลอด เอามาต่อ AMP ได้ไหมครับ
ได้ครับ
ใครช่วยหาวงจรดีๆให้ ผมให้ 4 หลอด NOS USA ( จะขอเพื่อนให้ ).
:shutup :shutup :shutup :shutup :shutup
-
O0 สุดยอดเลยครับ คุณพ่อน้องเปรียว คลังข้อมูล ผมมีอะไรสงสัยจะได้ถามบ้าง ;)
-
หลอดนี้ประมาณว่าเป็นหลอดเทตโธดใช้ในเครื่องส่งวิทยุ มีจุกแบบเดียวกับ 807
ถ้าผมทำก็คงเป็นซิงเกิลเอ็นด์ ดัดแปลงวงจรจาก 807 ครับ
อยากเอามาทำเครื่องส่ง AM เล่นจัง
-
หลอดนี้ประมาณว่าเป็นหลอดเทตโธดใช้ในเครื่องส่งวิทยุ มีจุกแบบเดียวกับ 807
ถ้าผมทำก็คงเป็นซิงเกิลเอ็นด์ ดัดแปลงวงจรจาก 807 ครับ
อยากเอามาทำเครื่องส่ง AM เล่นจัง
ผมกำลังคิดเอามาทำเครื่องส่งเหมือนกันครับ เพราะอยู่ใกลบ้าน จะได้ส่งวิทยุถึงบ้านแทนการโทรศัพย์ :clap :clap :clap
-
ภาคจ่ายไฟ
THANK YOUUUUUUUUUUUUUUUUUUUUUUUUUUUU
-
หลอดนี้ประมาณว่าเป็นหลอดเทตโธดใช้ในเครื่องส่งวิทยุ มีจุกแบบเดียวกับ 807
ถ้าผมทำก็คงเป็นซิงเกิลเอ็นด์ ดัดแปลงวงจรจาก 807 ครับ
อยากเอามาทำเครื่องส่ง AM เล่นจัง
ผมกำลังคิดเอามาทำเครื่องส่งเหมือนกันครับ เพราะอยู่ใกลบ้าน จะได้ส่งวิทยุถึงบ้านแทนการโทรศัพย์ :clap :clap :clap
ต้องฝึกเคาะรหัสมอร์สด้วยครับ ต๊อด....ต็อต....
...I...L...O...V...U... :yucky
-
ภาคจ่ายไฟสุดยอดไปเลยครับ....2X900V. :cold
-
ถาคจ่ายไฟ ;D ;D ;D ;D
-
ตาไวเจงๆพี่ magneto :yucky :yucky ........ แอบเข้าไปแก้มาแระ :whistling
-
The 6146 was used in the original Ampeg SVT bass guitar amplifier which used 6 of them to produce 300 watts. That amp had a reputation for blowing up, so they switched to 6550's in the later models. The schematic is in the book "A desktop reference of hip vintage guitar amps" by Gerald Weber. It may be on the web somewhere.
There is very little literature showing the use of this tube in HiFi applications especially SE. The tube was used in the modulator section of transmitters back in the 1950's, that is where the AF amp reference comes from. You could probably get them to work in a circuit that was designed for an 807, although the tubes are not that similar. Some resistor values would need tweaking, and the bias would need adjustment.
ลอกเขามาทั้งน้าน... 8)
-
ทำเป็นซิงเกิลเอ็นด์ก็ได้ อย่าใช้ไฟสูงนัก เอาพอขำๆ :cold
I think that you could try with 6L6/807 circuits in SE, some 400V on the plate, 200 regulated volts on the screens, and 6K OT... of course cathode resistor will need to be calculated.
-
http://www.diyaudio.com/forums/showthread/t-70571.html
ต้องก้อปข้อความมาไว้มั่ง ลางทีไปหาที่ต้นตอนอกประเทศแล้วเข้าไม่ได้
The maximum cathode current rating is 125mA per tube. If you were trying to drive a conventional 8 ohm speaker you would need a box full of these to build an OTL.
I think that you could get 5 watts per tube in triode connected SE but the low screen grid voltage points to pentode connection where 10 Watts per tube could be attained in SE.
These tubes would not work great in ultralinear due again to the low screen grid voltage rating. In push pull pentode mode the spec sheet claims 55 to 120 watts per pair, depending on how hard you push them.
I guess that your decision really depends on how much power you need (or want).