HTG2.club
Home Theater Guide webboard => มุม Thai DIY Audio => ข้อความที่เริ่มโดย: ดาวเหนือ ที่ 27 สิงหาคม, 2005, 01:09:56 pm
-
คุณ Taro กำลังหาเพื่อนร่วมซื้อ FET เบอร์ J309 เอามาทำ Reclock นะครับ...ผมเลยช่วยประกาศหาเพื่อนที่สนใจ
http://www.htg2.net/index.php?topic=3161.0
มีใครจะร่วมซื้อ FET เบอร์ J309 บ้างครับพอดีผมจะสั่งซื้อ จาก GTI แต่ต้องซื้อ 5 ตัวขึ้นไปผมใช้แค่ 2 ตัวเค้าไม่ขายก็อยากหาผู้ร่วมซื้อ ราคาก็ตามนี้ครับแต่ยังไม่รวมค่าส่ง
5+ ฿37.00
25+ ฿27.00
100+ ฿20.00
250+ ฿12.00
-
ผมก็เอาด้วยหนึ่งตัวครับ... ;)
-
บอกก่อนนะครับว่าพอดีผมจะมาทำ Kwak-7 ครับ ยังไงประมาณวันอังคารนี่แหละผมคงสั่ง order เลยผมคงรอไม่ไหวเพราะทาง GTI ต้องสั่งจากทางสิงคโปร์อีกที ถ้าไม่มีใครแชร์ผมก็งคงสั่งเอง 5 ตัวรวดเลย ;D ;D :'( :'(
-
ผมร่วมด้วย ช่วยซื้อ 1 ตัวครับ.... แต่ยังไม่รู้เอามาทำอะไรเลย ???
-
ผมร่วมด้วย ช่วยซื้อ 1 ตัวครับ.... แต่ยังไม่รู้เอามาทำอะไรเลย� ???
ถ้าคุณไทจะสั้งเพื่อมาทำ Clock 7 ต้องสั่ง AD8561 มาด้วยที่เดียวกันเลยเพราะเจ้า AD8561 หาซื้อที่บ้านหม้อไม่ได้ครับ
AD8561 ราคาตัวละประมาณ 280 บาท ไม่รวมค่าขนส่งครับ.... :)
-
AD8561 ราคาตัวละประมาณ 280 บาท ไม่รวมค่าขนส่งครับ....
มีใครสั่งซื้อหรือครับ จะได้แจม..แหะ แหะ
เมื่อวานลอง Gainclone ตัวใหม่ (Invert ปรับปรุงบางจุด) ทำภาค Power Supply พัง ทีแรกนึกว่าหม้อแปลงไปซ่ะแล้ว 800 กว่าบาทเชียว... ที่แท้ทำไดโอดพังไป 2 ตัว เดี๋ยวบ่ายๆ จะไปเซียร์ครับ
-
คุณไท......ผมแจ้งคุณทาโร่ให้แล้วนะครับ ;)
-
ทราบแล้วครับ
-
ขอบคุณทั้งสองท่านครับ.. ;D
ไว้ได้ของแล้ว สอนผมทำบ้างนะครับ...แหะ แหะ ::)
-
คุณลอง D/L เอาไปศึกษาก่อนแล้วกันนะครับ
http://http://www.diyaudio.com/forums/showthread.php?postid=199928#post199928
-
สรุปนะครับ
FET เบอร์ J309
คุณดาวเหนือ 1 ตัว
คุณไท 1 ตัว
น้อง Louis 2 ตัว
น้องกบ 2 ตัว
ผม 2 ตัว
ราคายังไม่รวมค่าส่งนะครับเดี๋ยวรู้ค่าส่งจะแจ้งให้ทราบอีกที
ผมคงหยุดรับแค่วันจันทร์ ตอน 15:00 นะครับแล้วคงจะสั่งเลย
-
�คุณ Taro โม CD เรียบร้อยหรือยังครับ แล้วลองเหรียญ 5 บาทด้วยหรือปล่าว ได้ผลอย่างไรเล่าสู่กันฟังด้วยครับ.. :)
-
จัดการเรียบร้อยแล้วครับ เปลี่ยน C เป็น OS-CON แล้ว เปลี่ยน Op-Amp เป็น OPA627 ต่อ เป็นแบบ Dual เสียงที่ได้ดีขึ้นมากครับ ตอนนี้เหลือแค่ลองตัว Kawk 7 ครับ ลืมไปลองเอาเหรีญ 5 แปะกับ Bluetack แล้วเสียงที่นิ่งขึ้นครับ ขอบคุณที่ให้คำแนะนำครับ
-
ผมร่วมด้วย 2 ตัวครับแล้ว IC หาที่ไหนได้ครับผมได้หาตัวอื่นๆสะสมมานานแล้ว
-
สรุปสั่งซื้อ
FET เบอร์ J309 = 14 ตัว
คุณดาวเหนือ 2 ตัว
คุณไท 2 ตัว
น้อง Louis 2 ตัว
น้องกบ 2 ตัว
คุณทาโร่ 2 ตัว
คุณ KVA 2 ตัว
คุณสันติ 2 ตัว
AD8561 = 7 ตัว (AD8561 ตัวละสองร้อยกว่าบาทไม่รวมค่าขนส่งนะครับ)
คุณดาวเหนือ 1 ตัว
คุณไท 1 ตัว
น้อง Louis 1 ตัว
น้องกบ 1 ตัว
คุณทาโร่ 1 ตัว
คุณ KVA 1 ตัว
คุณสันติ 1 ตัว
คุณทาโร่แจ้งมาว่าขอปิดการร่วมสั่งซื้อครับ.เพราะใจร้อนสั่งของไปแล้วครับ
ของได้ประมาณอาทิตย์หน้าครับ...ถ้าไม่มีปัญหา
-
ข้อมูลเพิ่มเติมครับ
FET เบอร์ J309 คุณทาโร่สั่งไป 15 ตัว ยังเหลืออีก 1 ตัวครับ...ท่านใดสนใจลงชื่อได้เลยครับ ;)
ของได้ประมาณอาทิตย์หน้าครับ...ถ้าไม่มีปัญหา
ของจะได้ประมาณ 2-3 อาทิตย์(14 วันทำการ)เพราะ AD8561 จะต้องเดินทางมาจากอังกฤษ เลยช้าหน่อย แต่FET เบอร์ J309 ของอยู่ที่สิงค์โปร์แล้วครับ...แต่เข้าคงส่งมาที่เดียวกันเลยนะครับ
-
ผมสั่งซื้อไปแล้วนะครับส่วนราคานั้นเดี๋ยวจะแจ้งให้ทราบอีกที
วงจรพร้อมอุปกรณ์
Hi,
Please find attached the latest version of the KWAK-CLOCK.
Compared with earlier versions it has more bass slam and punch and less
glare.
The pot is adjusted for best waveform on the scope (50% duty cycle).
You can use the crystal from the CDP.
The KWAK-CLOCK will work with any crystal in the range 8 to 24.576 MHz.
The KWAK-CLOCK will dramatically improve the sound of your gear and is
considered better than the LCaudio.
Instructions for installing are on the Audiocom and LCAudio website.
<http://www.lcaudio.dk>
With a 50 Ohm home-made probe a squarewave can be seen on the scope. My
home-made probe consists of a 50 Ohm coax cable and 50 Ohm from core to
ground at the scope end.
An ordinary probe gives kind of a distorted triangular wave shape.
If you have a scope with enough bandwith you will only see a squarewave if
you use a homemade probe of 50 Ohm coax cable terminated at the scope with
50 Ohm from core to shield. Standard probes distort the waveform. Measure
before the 0.01µF coupling cap!
Alternatively you can adjust the pot for +0.5 to +0.6V at pin 3 of the
comparator. (best measured at the cap connected to the wiper of the pot)
The idea is to connect the KWAK-CLOCK to the raw digital supply of the
CD-player. The main filtercaps of the player and the 2.2mH chokes and the
2200µF caps form a PI-filter effectively filtering any noise going in AND
out the clock-circuit.
The instructions are very simple:
Remove/desolder the crystal from the player and also remove the two small
caps attached to it. Solder the crystal to the KWAK-CLOCK PCB. Connect
powerleads red to + 9-+16V , yellow to -9-16V and ground. Connect the output
of the KWAK-CLOCK to one of the pads of the original crystal.. Which pad can
be determined from the schematic or the type of Digital Signal Processor
your player is using or by trial with a 1k resistor in series with the
clockoutput. Keep the pad that works and remove the 1k resistor.
Installation of the KWAK-CLOCK is worthwhile in any CDP!
Best regards,
ELSO
Partslist KWAK-CLOCK-7 with low noise regulators
1 resistor 47 Ohm
1 resistor 1k
2 resistor 820 ohm
2 resistor 2.7 k
1 resistor 21.5 k
3 resistor 27k
1 resistor 100k
1 resistor 10M
1 pot 2k Spectrol type 64W
1 cap ceramic NPO� 39 pF (marked 39)
1 cap ceramic NPO 68 pF (marked 68)
2 cap ceramic disc 0.01 µF (marked 103)
8 cap ceramic 0.1 µF (marked 104)
1 cap ceramic NPO 100pF (marked 100)
2 electrolytic cap 2200µF; 16V
2 cap 1µF polypropylene
2 inductor 2.2 mH (marked NEOSID 2,2k)
1 FET J309
1 IC AD8561AN
1 transistor BC550C
1 transistor BC560C
2 IC LM431
3 ferrite bead
1 PCB
-
ไม่ทราบท่านใดได้ออกแบบ PCB บ้างเปล่าครับจะดูมีระเบียบขึ้น สวยกันแบบไทยๆ
-
ตอนนี้ของได้รับแล้วนะครับ ส่วนจะให้จัดส่งยังไงช่วยแจ้งมาด้วยนะครับ
-
ตอนนี้ของได้รับแล้วนะครับ ส่วนจะให้จัดส่งยังไงช่วยแจ้งมาด้วยนะครับ
คุณทาโร่ช่วยสรุปค่าใช้จ่ายให้ด้วยครับ :)
-
คุณสันติครับผมสรุปค่าใช้จ่ายทาง Mail ให้แล้วนะครับ
รบกวนช่วยแจ้งด้วยนะครับว่าจะให้ส่งของยังไง
ส่วนของคุณ KVA เดี๋ยววันไหนว่างๆ จะแวะเอาไปให้ครับ
-
J309 +AD8561ยังพอมีเหลือไหมครับ อยากได้ซัก1ชุด :D
-
J309 +AD8561ยังพอมีเหลือไหมครับ อยากได้ซัก1ชุด :D
รู้สึกว่าคุณทาโร่จะเหลือแต่ J309 นะครับ :)
-
:-\ ว้ามาทีหลังเลย อดซะแล้ว :-[ ยังพอสั่งที่ไหนได้บ้าง ใครทำเสร็จแล้ว ช่วยลงรูปให้ดูหน่อยคราบ :o
-
ยังพอสั่งที่ไหนได้บ้าง
AD8561 ต้องสั่งจากต่างประเทศอย่างเดียวเลยครับ คงไม่มีร้านไหนสั่งมาเก็บเอาไว้ คุณทาโร่ได้เดินหาตามร้านอุปกรณ์อิเลคโทรนิคทั้งหมดแล้วครับ ไม่มีเลยต้องสั่งมากันเองครับ
-
สั่งที่ GTI (gti.co.th) ครับสั่งได้เลย ส่วน J309 มาแบ่งผมได้ครับเพราะ J309 สั่งขั้นต่ำ 5 ตัวครับ ส่วน AD8561 สั่งตัวเดียวได้ครับ