HTG2.club
Home Theater Guide webboard => มุม โฮมเธียเตอร์ (HT) => ข้อความที่เริ่มโดย: nanjang ที่ 17 กุมภาพันธ์, 2012, 02:45:02 pm
-
:(พอดี ถอดเก็บไว้นานประมาณ4-5 เดือน เอาออกมาต่อใหม่ทีนี้มันไม่ติดครับ กล่าวคือ เสียบปลั๊กไฟ ไฟเข้า ไฟสแตนด์บายสีแดงติด พอกดเพื่อเปิดเครื่องจะเปลี่ยนเป็นไฟเขียว หน้าจอมีบอกระดับเสียง อินพุท จำนวนลำโพงตามอินพุท สัญญาณเสียงเป็นแบบใหน ขึ้นมาครับ แต่สักพักก็จะกลับเป็นไฟแดงสแตนด์บายอีก ใช้เวลาจากการกดสัก 5 วินาทีได้ เป็นทุกครั้งเลยที่ลองกด เหมือนภาคขยายไม่ทำงาน (หรือเปล่า) ก่อนหน้าที่จะถอดอาการปกติทุกอย่างครับ เพื่อนๆใครมีประสบการณ์ช่วยแชร์กันหน่อยนะครับ ตอนนี้อยากดูหนังแย่แล้ว อิอิ หรือแนะนำร้านตรวจเช็คหน่อยก็ดีครับ ที่มีความรู้กับ Harman Kardon ผมอยู่ต่างจังหวัดครับ (กำแพงเพชร) ขอบคุณทุกความเห็นนะครับผม
-
ลองเช็คว่าสายลำโพงไม่มีการ short ของ + และ - เพราะเหมือนเข้า protection mode
ให้ถอดปลั๊กออก ทิ้งไว้สักพัก แล้วเสียบใหม่ให้ไฟ standby ขึ้น รออีก 2-3 ชมแล้วค่อยมาเปิดใหม่ เคยทำกับ AVR Denon ที่มีอาการคล้ายๆกันครับ ถ้าไม่หายลอง processor reset
Processor Reset
In the rare case where the units operation or the
displays seem abnormal, the cause may involve
the erratic operation of the systems memory or
microprocessor.
To correct this problem, first unplug the unit from
the AC wall outlet and wait at least three minutes. After the pause, reconnect the AC power
cord and check the units operation. If the system
still malfunctions, a system reset may clear the
problem.
To clear the AVR 5500s entire system memory
including tuner presets, output level settings,
delay times and speaker configuration data,
Firstput the unit in Standby by pressing the System Power Control button
Next, press the Tone Mode and the RDS buttons simultaneously.
The unit will turn on automatically and display the R E S E T message in the Main Information Display
Note that once you have cleared the memory in this manner, it is necessary to re-establish all system configuration
settings and tuner presets.
NOTE: Resetting the processor will erase any
configuration settings you have made for speakers, output levels, surround modes, digital input
assignments as well as the tuner presets. After a
reset the unit will be returned to the factory presets, and all settings for these items must be
reentered.
If the system is still operating incorrectly, there
may have been an electronic discharge or severe
AC line interference that has corrupted the memory or microprocessor.
If these steps do not solve the problem, consult
an authorized Harman Kardon service depot.
ถ้ายังไม่ได้อีกคงต้องส่งศูนย์ครับ
:D :D :D
-
ลองเช็คว่าสายลำโพงไม่มีการ short ของ + และ - เพราะเหมือนเข้า protection mode
ให้ถอดปลั๊กออก ทิ้งไว้สักพัก แล้วเสียบใหม่ให้ไฟ standby ขึ้น รออีก 2-3 ชมแล้วค่อยมาเปิดใหม่ เคยทำกับ AVR Denon ที่มีอาการคล้ายๆกันครับ ถ้าไม่หายลอง processor reset
Processor Reset
In the rare case where the units operation or the
displays seem abnormal, the cause may involve
the erratic operation of the systems memory or
microprocessor.
To correct this problem, first unplug the unit from
the AC wall outlet and wait at least three minutes. After the pause, reconnect the AC power
cord and check the units operation. If the system
still malfunctions, a system reset may clear the
problem.
To clear the AVR 5500s entire system memory
including tuner presets, output level settings,
delay times and speaker configuration data,
Firstput the unit in Standby by pressing the System Power Control button
Next, press the Tone Mode and the RDS buttons simultaneously.
The unit will turn on automatically and display the R E S E T message in the Main Information Display
Note that once you have cleared the memory in this manner, it is necessary to re-establish all system configuration
settings and tuner presets.
NOTE: Resetting the processor will erase any
configuration settings you have made for speakers, output levels, surround modes, digital input
assignments as well as the tuner presets. After a
reset the unit will be returned to the factory presets, and all settings for these items must be
reentered.
If the system is still operating incorrectly, there
may have been an electronic discharge or severe
AC line interference that has corrupted the memory or microprocessor.
If these steps do not solve the problem, consult
an authorized Harman Kardon service depot.
ถ้ายังไม่ได้อีกคงต้องส่งศูนย์ครับ
:D :D :D
ขอบคุณ คุณ nuummie นะครับ ผมลองเอาปลั๊กไฟออกสักพักนึง แล้วเสียบใหม่ ลองกดใหม่ก็เป็นเหมือนเดิมครับ ลองถอดสายลำโพง สายโคแอคเชียลออกทั้งหมด เสียบปลั๊กแล้วกดเปิดใหม่ ก็ไม่ได้อีก สุดท้ายลองรีเซต หน้าจอก็ขึ้นรีเซตนะ แต่ก็กลับมาสู่สถานะสแตนด์บายเหมือนเดิม :'(
ทำไงดี :(
สงสัยต้องส่งศูนย์ซะมั้งงานนี้
หรือน้องHK.คงเหนื่อย เปลี่ยนเป็น Pre/Pro ซะดีมั๊ง >:(
ยังงัยก็ขอบคุณ คุณ nuummie อีกครั้งนะครับ O0
-
ยินดีครับ พอดีเคยใช้ HK มาเหมือนกัน
เบอร์ บ.มหาจักร 02-256-0021 เบอร์ช่าง บ.มหาจักร 085-918-1401 น่าจะซ่อมได้ครับ
:D :D :D
-
ขอบคุณครับ :)