HTG2.club
Home Theater Guide webboard => มุม Thai DIY Audio => ข้อความที่เริ่มโดย: Wasin ที่ 10 มีนาคม, 2006, 07:36:11 pm
-
เผื่อใครจะทำเอาไว้ตอนทดสอบเครื่องตัวเองครับ :whistling ;)
http://www.headphoneamp.co.kr/bbs/zboard.php?id=diy_sijosae
ลองเปิดดูนะครับมีอะไรดีๆเยอะเหมือนกัน ถึงจะไม่ใช่หลอด
แฟนๆ headphone อาจจะชอบ
เสียอย่างเดียวเป็นภาษาเกาหลีครับ
-
วงจรครับ
Low Frequency Sinewave Generators
The two circuits below illustrate generating low frequency sinewaves by shifting the phase of the signal through an RC network so that oscillation occurs where the total phase shift is 360 degrees. The transistor circuit on the right produces a reasonable sinewave at the collector of the 3904 which is buffered by the JFET to yield a low impedance output. The circuit gain is critical for low distortion and you may need to adjust the 500 ohm resistor to achieve a stable waveform with minimum distortion. The transistor circuit is not recommended for practical applications due to the critical adjustments needed.
The op-amp based phase shift oscillator is much more stable than the single transistor version since the gain can be set higher than needed to sustain oscillation and the output is taken from the RC network which filters out most of the harmonic distortion. The sinewave output from the RC network is buffered and the amplitude restored by the second (top) op-amp which has gain of around 28dB. Frequency is around 600 Hz for RC values shown (7.5K and 0.1uF) and can be reduced by proportionally increasing the network resistors (7.5K). The 7.5K value at pin 2 of the op-amp controls the oscillator circuit gain and is selected so that the output at pin 1 is slightly clipped at the positive and negative peaks. The sinewave output at pin 7 is about 5 volts p-p using a 12 volt supply and appears very clean on a scope since the RC network filters out most all distortion occurring at pin 1.
-
ผมลองแล้วคือต่อตามวงจรด้านซ้ายมือค่าอุปกรณ์ไม่ตรงกับรูป layout คลื่น sine wave สวยครับแต่มันได้ประมาณ 600 Hz เดี๋ยวลองเปลี่ยนค่าดู
-
ครับ ต้องเปลี่ยนค่า 7.5K ที่ต่อกับ C 0.1uF ทั้ง 3 ตัว
เป็นค่า 3.9K ตามรูป layout น่ะครับ ถึงจะได้ 1 KHz
-
ขอบคุณครับ ไม่อ่านได้ภาษาประกิตก่อนทำ เฮอ! ไม่รอบครอบเลยเรา
-
น่าสนใจดีครับ เขาบอกสูตรในการคำนวณไหมครับ อยากเอาไปgenerate low frequency sinewave อย่าง 60Hz นะครับ
-
เค้าไม่ได้บอกสูตรคำนวนไว้เลยครับ บอกไว้แค่เนี้ยน่ะครับ
Frequency is around 600 Hz for RC values shown (7.5K and 0.1uF) and can be reduced by proportionally increasing the network resistors (7.5K).
-
ถ้าอยากใด้แค่ 60Hz พอจะเป็นไปใด้ไหมครับและถ้าเป็นไปใด้ต้องปรัค่าตรงไหนบ้างครับ
-
ขอความรู้หน่อยนะครับ จากวงจรนี้ถ้าผมจะตัดในส่วนของ square wave gen ออกไปผมต้องตัดส่วนไหนออกบ้างครับ
ข้อความประกอบครับ
566 function generator provides triangleoutput at 60 Hz with frequency stability better than ±0.02%/°C. 540 power driver feeds six-transistor power output stage. Transformer load attenuates third harmonic, giving output very close to pure 60-Hz sine wave. 566 also provides square-wave out-put for other pu rposes
-
แจ๋มเลยครับ น่าสน
อีกเวบหนึ่งที่มีวิธีคำนวณครับ คิดว่าคำนวณเหมือนกัน เพราะเป็นเวนบริดเช่นกัน แต่sine wave น่าจะสเตเบิลกว่าเหมาะกับการขับturntable มากกว่า คือเวบที่แนบนี้ครับ
www.piclist.com/images/www/hobby_elec/e_ckt18.htm
-
วงจรที่น้องจ๊วตแปะมา. Frq gen จะอยู่ก่อนเข้าวอลลุ่ม(VR1)
นะ. หลังวอลลุ่มเป็นต้นไปเป็นภาคขยายขนาดลูกคลื่นก่อนสเตปอับเป็นไฟสูง
-
ไม่ลอง XR2206 ดูบ้างหรือครับ?